Furnace Filters 101: Types, Sizes and How Often to Change Them

Homeowner sliding a clean pleated furnace filter into a furnace before winter

Furnace filters in London and Strathroy homes should be checked monthly and replaced on a schedule set by thickness: a one-inch pleated filter about every three months, a four- or five-inch MERV 16 media filter about once a year. A clean filter protects the blower and heat exchanger and keeps room air clean. Natural Resources Canada warns that a dirty filter can increase energy costs and damage your system.

What Does a Furnace Filter Actually Do?

A forced-air furnace pulls air from every room through the return ducts, heats it and sends it back, and the filter sits in that return path so all of the air in the house passes through it several times a day. It protects the equipment first: dust that gets past it coats the blower wheel, the heat exchanger and the indoor coil of an air conditioner or heat pump, cutting airflow and efficiency year after year. It also traps pet dander, pollen, mould spores and smoke, and how well it does that depends on its MERV rating.

When a filter clogs, airflow drops, the heat exchanger overheats and the high-limit switch shuts the burners down early, so the furnace cycles on and off and rooms never quite warm up. Air Design Services lists short cycling and uneven heating among the top signs a furnace needs maintenance, and a plugged filter is the first thing to rule out before booking a furnace repair.

What Are the Main Types of Furnace Filters?

Three kinds of disposable filter cover almost every furnace in Southwestern Ontario, and the difference comes down to surface area and density. Washable electrostatic filters exist too, but most sit low on the MERV scale.

Fibreglass flat-panel filters

The blue or green one-inch filter that costs a few dollars is spun fibreglass on a cardboard frame. It keeps lint and hair out of the blower, does very little for the air you breathe at MERV 1 to 4, and loads quickly, so it needs replacing monthly in heating season.

Pleated one-inch filters

Pleating folds far more material into the same one-inch frame, so a pleated filter catches smaller particles, commonly MERV 8 to 13, while leaving enough open area for the blower. Lennox, the brand Air Design has installed since 1982, recommends changing one-inch disposable filters every three months, and about monthly where there are allergies, pets or dust buildup.

Media filters in a cabinet

A media filter is a deep box of pleated material, four to five inches thick, in its own cabinet between the return duct and the furnace. Its depth gives it several times the surface area of a one-inch filter, so it reaches MERV 16 without choking airflow. The Lennox Healthy Climate 16 media air cleaner on Air Design’s air cleaners page, sold by Lennox today as the Carbon Clean 16, takes a MERV 16 filter that Lennox rates for up to 12 months and that removes up to 95 percent of particles down to 0.3 microns.

What Do MERV Ratings Mean, and How High Should You Go?

MERV stands for Minimum Efficiency Reporting Value. The scale runs from 1 to 16 and comes from a test method developed by ASHRAE. The U.S. Environmental Protection Agency’s MERV table shows what the numbers mean: a MERV 1 to 4 filter captures less than 20 percent of 3 to 10 micron particles (visible dust and pollen), a MERV 8 captures at least 70 percent of them, a MERV 13 captures at least 85 percent of 1 to 3 micron particles and half of the 0.3 to 1 micron range where smoke and bacteria live, and a MERV 16 captures at least 95 percent across all three ranges.

The EPA’s advice is to choose at least a MERV 13 if you upgrade, or as high a rating as your system fan and filter slot can accommodate, and to ask an HVAC technician which filter will work with your system. A dense MERV 13 forced into a one-inch slot on an older blower can cut airflow enough to cause the overheating described above. For hospital-grade filtration the answer is usually a media cabinet, and a free in-home consultation with Air Design Services will confirm whether your furnace and ductwork can take one.

How Do You Find the Right Furnace Filter Size for a London Home?

Every filter has two sizes. The nominal size is the rounded number printed in large type on the frame, such as 16x25x1, and the actual size is the true measurement, always a little smaller. Air Design’s 16x25x5 MERV 16 filter measures 15 3/4 by 24 3/4 by 4 3/8 inches, and its 20x25x5 measures 19 3/4 by 24 3/4 by 4 3/8.

Lennox suggests the simplest route: read the size printed on the frame of the old filter. If the slot is empty, measure the opening’s length, width and depth, round each up to the nearest inch, and bring those numbers to the store or to Air Design. Note the thickness too: a five-inch cabinet should never be loaded with a stack of one-inch filters.

How Often Should You Change Your Furnace Filter in London and Strathroy?

The short answer is when it is dirty, so a monthly look matters more than any calendar rule. Hold the filter up to a light; if no light comes through, it is done. Here are the manufacturer and government starting points.

  • One-inch fibreglass: replace every 30 days while the furnace is running regularly.
  • One-inch pleated: every three months per Lennox, and monthly in homes with pets, allergies or heavy dust.
  • Four- or five-inch media: Lennox rates the Carbon Clean 16 filter for up to 12 months, and Air Design sells its MERV 16 replacements as yearly disposable filters. Check it at six months in a busy household.
  • Heat pumps and hybrid systems: the blower runs for cooling in summer and heating in winter, so the filter loads year-round. As the cold climate heat pump guide on this site notes, Natural Resources Canada recommends a change or cleaning every three months.
  • Washable: rinse monthly and reinstall only when fully dry.

Pets, renovations, wood smoke and a thermostat fan set to “on” instead of “auto” all shorten those intervals. Natural Resources Canada’s home heating and cooling maintenance guide says to follow your owner’s manual on filter changes and to book an annual pre-season check-up with a licensed and insured contractor, which is what a furnace maintenance visit in London from Air Design covers, filter included.

How Do You Change a Furnace Filter?

  1. Turn the furnace off. Set the thermostat to off or flip the power switch on the side of the cabinet so the blower cannot start while the slot is open.
  2. Find the filter. Look for a slot with a removable cover where the return duct meets the furnace, inside the blower compartment door, or in a separate media cabinet.
  3. Slide the old filter out and read it. Note the size on the frame and the direction of the airflow arrow, then vacuum the track and check for gaps where air could bypass the filter.
  4. Insert the new filter with the arrow toward the furnace. Make sure it sits fully in the track with no gaps, then close the cover.
  5. Date it and set a reminder. Write the date on the frame edge, restore power and put the next check in your phone for 30 days out.

Frequently Asked Questions About Furnace Filters in London, Ontario

Which way does the arrow on a furnace filter point?

Toward the furnace and away from the return duct, because the arrow shows the direction of airflow. Installed backwards, a filter still catches dust at first, but the frame and pleats are built to take pressure from one side, so it loads unevenly and can collapse into the slot.

Is a MERV 16 filter too strong for my furnace?

Not in a four- or five-inch media cabinet. The trouble comes from forcing a very dense one-inch filter into a slot designed for fibreglass. If your furnace only has a one-inch slot, ask about adding a media cabinet at your next furnace tune-up.

Where can I buy MERV 16 replacement filters in London or Strathroy?

Air Design Services stocks MERV 16 replacements in 16x25x5, 20x20x5 and 20x25x5 for Lennox Healthy Climate cabinets (models HCC16-28, HCC14-23 and HCC20-28) and, in the 16×25 and 20×25 sizes, the matching Honeywell F25 cabinets. Check the model number on your cabinet label, then contact the London or Strathroy office.

Does Air Design change the filter during a furnace tune-up?

Yes. Cleaning and filter replacement is part of every furnace maintenance service: technicians clean the internal components, replace or recommend the right filter, and finish with a written report. Still dusty afterwards? Read about winter indoor air quality and ask about a whole-home media air cleaner.

Keep Your Furnace Breathing With Air Design Services

Air Design Services has heated and cooled homes in London and Strathroy since 1982 as a full-line Lennox dealer, with fully licensed, factory-trained technicians who service every furnace brand. The team can match a filter to your system, add a media cabinet to an older furnace and show you how to change it. Call 519-963-0572 in London (39 Enterprise Drive) or 519-246-1224 in Strathroy (19 Collins Way), or contact Air Design Services online to get your furnace ready for the heating season.

This post was written by air_admin

October 28, 2026